 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| (R) TS914 RAIL TO RAIL CMOS QUAD OPERATIONAL AMPLIFIER . . . . . . . RAIL TO RAIL INPUT AND OUTPUT VOLTAGE RANGES SINGLE (OR DUAL) SUPPLY OPERATION FROM 2.7V TO 16V EXTREMELY LOW INPUT BIAS CURRENT : 1pA TYP LOW INPUT OFFSET VOLTAGE : 5mV max. SPECIFIED FOR 600 AND 100 LOADS LOW SUPPLY CURRENT : 200A/Ampli SPICE MACROMODEL INCLUDED IN THIS SPECIFICATION N DIP14 (Plastic Package) D SO14 (Plastic Micropackage) ORDER CODES Part Number TS914I/AI Temperature Range -40, +125 C o Package N * D * PIN CONNECTIONS (top view) DESCRIPTION The TS914 is a RAIL TO RAIL quad CMOS operational amplifier designed to operate with a single or dual supply voltage. The input voltage range Vicm includes the two supply rails VCC+ and VCC-. The output reaches : * VCC- +50mV VCC+ -50mV with RL = 10k * VCC- +350mV VCC+ -350mV with RL = 600 This product offers a broad supply voltage operating range from 2.7V to 16V and a supply current of only 200A/amp. (VCC = 3V). Source and sink output current capability is typically 40mA (at VCC = 3V), fixed by an internal limitation circuit. STMicroelectronics is offering a dual op-amp with the same features : TS912. April 1999 Output 1 Inverting Input 1 Non-inve rtin g Input 1 V CC + Non-inve rting Input 2 Invert ing Input 2 Output 2 1 2 3 4 5 6 7 + + + + 14 13 12 11 10 9 8 Output 4 Invertin g Input 4 Non-inve rtin g Input 4 VCC Non-inve rtin g Input 3 Invertin g Input 3 Output 3 1/13 TS914 SCHEMATIC DIAGRAM (1/4 TS914) VCC Non-inverting Input Inte rnal Vre f Inverting Input O utput VCC ABSOLUTE MAXIMUM RATINGS Symbol VCC Vid Vi Iin Io Toper Tstg Notes : Parameter Supply Voltage - (note 1) Differential Input Voltage - (note 2) Input Voltage - (note 3) Current on Inputs Current on Outputs Operating Free Air Temperature RangeI Storage Temperature Value 18 18 -0.3 to 18 50 130 -40 to +125 -65 to +150 Unit V V V mA mA o o C C 1. All voltage values, except differential voltage are with respect to network ground terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. The magnitude of input and output voltages must never exceed VCC+ +0.3V. OPERATING CONDITIONS Symbol VCC Vicm Supply Voltage Common Mode Input Voltage Range - Parameter Value 2.7 to 16 VCC -0.2 to VCC +0.2 + Unit V V 2/13 TS914 ELECTRICAL CHARACTERISTICS VCC+ = 3V, VCC- = 0V, RL,CL connected to VCC/2, Tamb = 25oC (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage (V ic = Vo = VCC/2) Tmin. Tamb Tmax. DVio Iio Iib ICC CMR SVR Avd VOH TS914 TS914A TS914 TS914A Min. TS914I/AI Typ. Max. 10 5 12 7 5 1 100 200 1 150 300 200 300 400 70 70 10 Unit mV Input Offset Voltage Drift Input Offset Current - (note 1) Tmin. Tamb Tmax. Input Bias Current - (note 1) Tmin. Tamb Tmax. Supply Current (per amplifier, AVCL = 1, no load) Tmin. Tamb Tmax. Common Mode Rejection Ratio Vic = 0 to 3V, Vo = 1.5V Supply Voltage Rejection Ratio (VCC+ = 2.7 to 3.3V, VO = VCC /2) Large Signal Voltage Gain (RL = 10k, VO = 1.2V to 1.8V) Tmin. Tamb Tmax. High Level Output Voltage (V id = 1V) RL = 10k RL = 600 RL = 100 Tmin. Tamb Tmax. RL = 10k RL = 600 RL = 10k RL = 600 RL = 100 Tmin. Tamb Tmax. RL = 10k RL = 600 - Source (Vo = VCC ) + Sink (Vo = VCC ) V/oC pA pA A dB 40 3 2 2.9 2.3 2.8 2.1 dB V/mV V 2.96 2.6 2 VOL Low Level Output Voltage (Vid = -1V) 50 300 900 100 400 150 600 40 40 0.8 mV Io GBP SR+ SRm en VO1/VO2 Output Short Circuit Current (Vid = 1V) mA MHz V/s Gain Bandwidth Product (AVCL = 100, RL = 10k, CL = 100pF, f = 100kHz) Positive Slew Rate AVCL = 1, RL = 10k, Vi =1.3V to 1.7V, CL = 100pF Negative Slew Rate Phase Margin Equivalent Input Noise Voltage (Rs = 100, f = 1kHz) Channel Separation (f = 1kHz) 0.5 0.4 30 30 120 V/s Degrees nV Hz dB Note 1 : Maximum values including unavoidable inaccuracies of the industrial test. 3/13 TS914 ELECTRICAL CHARACTERISTICS VCC+ = 5V, VCC- = 0V, RL,CL connected to VCC/2, Tamb = 25oC (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage (V ic = Vo = VCC/2) Tmin. Tamb Tmax. DVio Iio Iib ICC CMR SVR Avd VOH TS914 TS914A TS914 TS914A Min. TS914I/AI Typ. Max. 10 5 12 7 5 1 100 200 1 150 300 230 350 450 75 80 30 Unit mV Input Offset Voltage Drift Input Offset Current - (note 1) Tmin. Tamb Tmax. Input Bias Current - (note 1) Tmin. Tamb Tmax. Supply Current (per amplifier, AVCL = 1, no load) Tmin. Tamb Tmax. Common Mode Rejection Ratio Vic = 1.5 to 3.5V, Vo = 2.5V Supply Voltage Rejection Ratio (VCC+ = 3 to 5V, VO = VCC /2) Large Signal Voltage Gain (RL = 10k, VO = 1.5V to 3.5V) Tmin. Tamb Tmax. High Level Output Voltage (V id = 1V) RL = 10k RL = 600 RL = 100 Tmin. Tamb Tmax. RL = 10k RL = 600 RL = 10k RL = 600 RL = 100 Tmin. Tamb Tmax. RL = 10k RL = 600 - Source (Vo = VCC ) + Sink (Vo = VCC ) V/oC pA pA A dB 50 50 10 7 4.90 4.25 4.8 4.1 dB V/mV V 4.95 4.65 3.7 VOL Low Level Output Voltage (Vid = -1V) 50 350 1400 100 500 150 750 45 45 60 60 0.9 mV Io GBP SR+ SRm Output Short Circuit Current (Vid = 1V) mA MHz V/s Gain Bandwidth Product (AVCL = 100, RL = 10k, CL = 100pF, f = 100kHz) Positive Slew Rate AVCL = 1, RL = 10k, Vi =1V to 4V, CL = 100pF Negative Slew Rate Phase Margin 0.8 0.5 30 V/s Degrees Note 1 : Maximum values including unavoidable inaccuracies of the industrial test. 4/13 TS914 ELECTRICAL CHARACTERISTICS VCC+ = 10V, VCC- = 0V, RL,CL connected to VCC/2, Tamb = 25oC (unless otherwise specified) Symbol Vio Parameter Input Offset Voltage (Vic = Vo = VCC/2) Tmin. Tamb Tmax. DVio Iio Iib ICC CMR SVR Avd VOH TS914 TS914A TS914 TS914A Min. TS914I/AI Typ. Max. 10 5 12 7 5 1 100 200 1 150 300 400 600 700 75 70 80 60 Unit mV Input Offset Voltage Drift Input Offset Current - (note 1) Tmin. Tamb Tmax. Input Bias Current - (note 1) Tmin. Tamb Tmax. Supply Current (per amplifier, A VCL = 1, no load) Tmin. Tamb Tmax. Common Mode Rejection Ratio Vic = 3 to 7V, Vo = 5V Vic = 0 to 10V, Vo = 5V Supply Voltage Rejection Ratio (VCC+ = 5 to 10V, VO = VCC /2) Large Signal Voltage Gain (RL = 10k, VO = 2.5V to 7.5V) Tmin. Tamb Tmax. High Level Output Voltage (Vid = 1V) R L = 10k R L = 600 R L = 100 Tmin. Tamb Tmax. R L = 10k R L = 600 R L = 10k R L = 600 R L = 100 Tmin. Tamb Tmax. R L = 10k R L = 600 - Source (Vo = VCC ) + Sink (Vo = VCC ) V/oC pA pA A dB dB V/mV V 50 50 20 15 9.85 9.2 9.8 9 9.95 9.35 7.8 VOL Low Level Output Voltage (Vid = -1V) 50 650 2300 150 800 150 900 45 45 60 60 1.3 mV Io GBP SR + SRm en THD Cin VO1/VO2 Output Short Circuit Current (Vid = 1V) mA MHz V/s Gain Bandwidth Product (AVCL = 100, RL = 10k, CL = 100pF, f = 100kHz) Positive Slew Rate AVCL = 1, RL = 10k, Vi = 2.5V to 7.5V, CL = 100pF Negative Slew Rate Phase Margin Equivalent Input Noise Voltage (Rs = 100, f = 1kHz) Total Harmonic Distortion (AVCL = 1, RL = 10k, CL = 100pF, VO = 4.75V to 5.25V, f = 1kHz) Input Capacitance Channel Separation (f = 1kHz) 1.3 0.8 40 30 0.024 1.5 120 V/s Degrees nV Hz % pF dB Note 1 : Maximum values including unavoidable inaccuracies of the industrial test. 5/13 TS914 TYPICAL CHARACTERISTICS Figure 1 : Supply Current (each amplifier) vs Supply Voltage SUPPLY CURRENT, I CC ( A) Figure 2 : Input Bias Current vs Temperature 10 0 INPUT BIAS CURRENT, I ib (pA) 600 500 400 300 200 100 0 4 8 12 16 SUPP LY VOLTAGE, V CC (V) Tamb = 25 C A VC L = 1 V O = VCC / 2 VCC = 10V V i = 5V No load 10 1 25 50 75 10 0 125 TEMPERATURE, T amb ( C) Figure 3a : High Level Output Voltage vs High Level Output Current 5 OUTPUT VOLTAGE, VOH (V) Figure 3b : High Level Output Voltage vs High Level Output Current 20 T amb = 25 C Vid = 100mV VCC = +16V 4 3 2 1 0 VCC = +5V OUTPUT VOLTAGE, VOH (V) T amb = 25 C V id = 100mV 16 12 VCC = +10V 8 4 0 VCC = +3V -70 -40 -20 0 -70 -40 -20 0 OUTPUT CURRENT, IOH (mA) OUTP UT CURRENT, IOH (mA) Figure 4a : Low Level Output Voltage vs Low Level Output Current 5 4 3 2 1 T amb = 25 C V id = -100mV Figure 4b : Low Level Output Voltage vs Low Level Output Current 10 OUTPUT VOLTAGE, VOL (V) OUTPUT VOLTAGE, V OL (V) VCC = +5V 8 6 4 2 T a mb = 25 C V id = -100mV VCC = +3V VCC = 16V VCC = 10V 0 30 50 70 90 0 30 50 70 90 OUTP UT CURRENT, I OL (mA) OUTP UT CURRENT, I OL (mA) 6/13 TS914 Figure 5a : Gain and Phase vs Frequecy Figure 5b : Gain and Phase vs Frequecy 50 40 GAIN 0 50 40 GAIN 0 45 P has e Margin Ga in Ba ndwidth P roduct PHASE (Degrees) GAIN (dB) PHASE Ta mb = 25 C VCC = 10V R L = 10k C L = 100pF AVCL = 100 20 10 0 -10 10 2 Ga in Ba ndwidth P roduct P ha s e Ma rgin GAIN (dB) 30 45 90 135 180 30 20 10 0 10 10 2 P HASE Tamb = 25 C VCC = 1 0V R L = 600 C L = 100pF A VCL = 100 90 135 180 10 3 10 10 10 FREQUENCY, f (Hz) 4 5 6 10 7 10 3 10 10 10 FREQUENCY, f (Hz) 4 5 6 10 7 Figure 6a : Gain Bandwidth Product vs Supply Voltage GAIN BANDW. PROD., GBP (kHz) 1800 1400 1000 Figure 6b : Gain bandwidth Product vs Supply Voltage GAIN BANDW. PROD., GBP (kHz) 180 0 14 00 1 000 6 00 20 0 Ta mb = 25 C R L = 10k C L = 100pF Ta mb = 25 C R L = 600 C L = 100pF 600 200 0 4 8 12 16 0 4 8 12 16 SUP P LY VOLTAGE, VCC (V) S UP P LY VOLTAGE, VCC (V) Figure 7a : Phase Margin vs Supply Voltage PHASE MARGIN, m (Degrees) 60 50 40 30 20 Figure 7b : Phase Margin vs Supply Voltage PHASE MARGIN, m (Degrees) 60 50 40 30 20 Tamb = 25 C R L = 10k C L = 10 0pF Tamb = 25 C R L = 6 00 C L = 1 00pF 0 4 8 12 16 0 4 8 12 16 S UP PLY VOLTAGE, VCC (V) S UP P LY VOLTAGE, VCC (V) 7/13 PHASE (Degrees) TS914 Figure 8 : Input Voltage Noise vs Frequency EQUIVALENT INPUT VOLTAGE NOISE (nV/VHz) 150 100 VCC = 10V Tamb = 25 C R S = 100 50 0 10 1000 100 FREQUENCY (Hz) 10000 8/13 TS914 MACROMODEL RAIL TO RAIL INPUT AND OUTPUT VOLTAGE RANGES STANDBY POSITION : REDUCED CONSUMPTION (1A) AND HIGH IMPEDANCE OUTPUTS SINGLE (OR DUAL) SUPPLY OPERATION FROM 2.7V TO 16V (1.35V to 8V) . . . . . . . . EXTREMELY LOW INPUT BIAS CURRENT : 1pA TYP LOW INPUT OFFSET VOLTAGE : 1.5mV max. SPECIFIED FOR 600 AND 100 LOADS LOW SUPPLY CURRENT : 400A/Ampli SPEED : 1.3MHz - 1.3V/s Applies to : TS914I,AI,BI ** Standard Linear Ics Macromodels, 1993. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIV E POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TS914_3 1 3 2 4 5 (analog) ********************************************************** .MODEL MDTH D IS=1E-8 KF=6.564344E-14 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 6.500000E+00 RIN 15 16 6.500000E+00 RIS 11 15 1.271505E+01 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0.000000E+00 VOFN 13 14 DC 0 IPOL 13 5 4.000000E-05 CPS 11 15 2.125860E-08 DINN 17 13 MDTH 400E-12 VIN 17 5 0.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 0.000000E+00 FCP 4 5 VOFP 5.000000E+00 FCN 5 4 VOFN 5.000000E+00 * AMPLIFYING STAGE FIP 5 19 VOFP 2.750000E+02 FIN 5 19 VOFN 2.750000E+02 RG1 19 5 1.916825E+05 RG2 19 4 1.916825E+05 CC 19 29 2.200000E-08 HZTP 30 29 VOFP 1.3E+03 HZTN 5 30 VOFN 1.3E+03 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 3800 VIPM 28 4 150 HONM 21 27 VOUT 3800 VINM 5 27 150 EOUT 26 23 19 5 1 VOUT 23 5 0 ROUT 26 3 75 COUT 3 5 1.000000E-12 DOP 19 68 MDTH 400E-12 VOP 4 25 1.724 HSCP 68 25 VSCP1 0.8E8 DON 69 19 MDTH 400E-12 VON 24 5 1.7419107 HSCN 24 69 VSCN1 0.8E+08 VSCTHP 60 61 0.0875 ** VSCTHP = le seuil au dessus de vio * 500 ** c.a.d 275U-000U dus a l'offset DSCP1 61 63 MDTH 400E-12 VSCP1 63 64 0 ISCP 64 0 1.000000E-8 DSCP2 0 64 MDTH 400E-12 DSCN2 0 74 MDTH 400E-12 ISCN 74 0 1.000000E-8 VSCN1 73 74 0 DSCN1 71 73 MDTH 400E-12 VSCTHN 71 70 -0.55 ** VSCTHN = le seuil au dessous de vio * 2000 ** c.a.d -375U-000U dus a l'offset ESCP 60 0 2 1 500 ESCN 70 0 2 1 -2000 .ENDS 9/13 TS914 Applies to : TS914I,AI,BI ** Standard Linear Ics Macromodels, 1993. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIV E POWER SUPPLY * 5 NEGATIVE POWER SUPPLY * 6 STANDBY .SUBCKT TS914_5 1 3 2 4 5 (analog) ********************************************************** .MODEL MDTH D IS=1E-8 KF=6.564344E-14 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 6.500000E+00 RIN 15 16 6.500000E+00 RIS 11 15 7.322092E+00 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0.000000E+00 VOFN 13 14 DC 0 IPOL 13 5 4.000000E-05 CPS 11 15 2.498970E-08 DINN 17 13 MDTH 400E-12 VIN 17 5 0.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 0.000000E+00 FCP 4 5 VOFP 5.750000E+00 FCN 5 4 VOFN 5.750000E+00 ISTB0 5 4 500N * AMPLIFYING STAGE FIP 5 19 VOFP 4.400000E+02 FIN 5 19 VOFN 4.400000E+02 RG1 19 5 4.904961E+05 RG2 19 4 4.904961E+05 CC 19 29 2.200000E-08 HZTP 30 29 VOFP 1.8E+03 HZTN 5 30 VOFN 1.8E+03 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 3800 VIPM 28 4 230 HONM 21 27 VOUT 3800 VINM 5 27 230 EOUT 26 23 19 5 1 VOUT 23 5 0 ROUT 26 3 82 COUT 3 5 1.000000E-12 DOP 19 68 MDTH 400E-12 VOP 4 25 1.724 HSCP 68 25 VSCP1 0.8E+08 DON 69 19 MDTH 400E-12 VON 24 5 1.7419107 HSCN 24 69 VSCN1 0.8E+08 VSCTHP 60 61 0.0875 ** VSCTHP = le seuil au dessus de vio * 500 ** c.a.d 275U-000U dus a l'offset DSCP1 61 63 MDTH 400E-12 VSCP1 63 64 0 ISCP 64 0 1.000000E-8 DSCP2 0 64 MDTH 400E-12 DSCN2 0 74 MDTH 400E-12 ISCN 74 0 1.000000E-8 VSCN1 73 74 0 DSCN1 71 73 MDTH 400E-12 VSCTHN 71 70 -0.55 ** VSCTHN = le seuil au dessous de vio * 2000 ** c.a.d -375U-000U dus a l'offset ESCP 60 0 2 1 500 ESCN 70 0 2 1 -2000 .ENDS 10/13 TS914 ELECTRICAL CHARACTERISTICS VCC+ = 3V, VCC- = 0V, RL,CL connected to VCC/2, Tamb = 25oC (unless otherwise specified) Symbol Vio Avd ICC Vicm VOH VOL Isink Isource GBP SR m RL = 600 RL = 600 VO = 3V VO = 0V RL = 10k, CL = 100pF, F = 100kHz RL = 10k, CL = 100pF RL = 10k No load, per operator Conditions Value 0 10 100 -0.2 to 3.2 2.6 300 40 40 0.8 0.5 30 Unit mV V/mV A V V mV mA mA MHz V/s Degrees 11/13 TS914 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Dimensions a1 B b b1 D E e e3 F i L Z Min. 0.51 1.39 Millimeters Typ. Max. 1.65 Min. 0.020 0.055 Inches Typ. Max. 0.065 0.5 0.25 20 8.5 2.54 15.24 7.1 5.1 3.3 1.27 2.54 0.050 0.020 0.010 0.787 0.335 0.100 0.600 0.280 0.201 0.130 0.100 12/13 TS914 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (so) Dimensions A a1 a2 b b1 C c1 D E e e3 F G L M S Min. 0.1 0.35 0.19 Millimeters Typ. Max. 1.75 0.2 1.6 0.46 0.25 45o (typ.) Min. 0.004 0.014 0.007 Inches Typ. Max. 0.069 0.008 0.063 0.018 0.010 0.5 8.55 5.8 1.27 7.62 3.8 4.6 0.5 4.0 5.3 1.27 0.68 8 (max.) o 0.020 8.75 6.2 0.336 0.228 0.050 0.300 0.150 0.181 0.020 0.157 0.208 0.050 0.027 0.334 0.244 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publ ication supersedes and replaces all infor mation previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. (c) The ST logo is a trademark of STMicroelectronics (c) 1999 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. (c) http://www.st.com 13/13 |
Price & Availability of TS914
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |